You can have calibre auto import from a folder. Though be careful because it deletes them from that folder (you might want to do single direction sync into that folder).
And if you share the db with calibre-web or have some other sync method that works, you should be good to go.
Yes, they share the database. Yes, I add the books to calibre. I think I have it as read only for calibre-web.
Regarding overcomplication, I admit the initial setup took a while. But I’ve had it running for a couple years now with no major issues.
There’s a docker that essentially sets up a web VNC for Calibre. I do this for file conversion, DRM removal (only books I buy), etc.
Then I use Calibre-web for the OPDS server and nice web UI.
I’ve been looking into this as well and just bought my first components.
I’m trying Meshtastic first and then will try Meshcore.
What does everybody think of Reticulum Network and RNode? It honestly seems superior conceptually to Meshtastic/Meshcore, but I’m not sure how good it is in practice or if anybody is actually using it.
Absolutely. When you’re making a book cover, a pretty typical method is to take book board (chipboard-like material, similar to the back cover of notebooks) and glue it on book cloth or paper. Then you fold over edges of the cloth/paper. You don’t need to cover the inside because that’s where the actual pages of the book will be, but you need some overlap (e.g. 25mm).
But the corner is a bit tricky. If you don’t trim at all, you have an extra triangle of folded paper that gets in the way. If you cut it off too close to the book board, you will see the board peeking through. So you want to cut the corner off with a little gap. And if you get the angle wrong, the fold doesn’t look quite right. This jig gives both spacing and angle, and it has an added bonus of the notches to let you mark your cuts for the fold over on each side.
The first 30 seconds of this video illustrate it pretty well: https://www.youtube.com/watch?v=N4IzpDqbHqU
I really like Build123d. I hope someday the model sites like Printables and Makerworld support it like they do OpenSCAD.
Nice, I’ll take a look. How is the mobile experience?
Yeah, no problem.
This is my first attempt at posting a comment with pictures, but hopefully these show up:
Yes. When I tried it, it was not very stable and the shortcuts didn’t really work on mobile. But I know a lot has changed, so I’ve been meaning to go back and give it another shot.
Backlinking is when you link to a page, it links back.
For example, if I have a daily journal, I can say Fixed a problem with my [[Raspberry Pi]] setup... and then a few weeks later I can say Found a new use for [[Raspberry Pi]]..., etc.
Now when I go to the Raspberry Pi page, it shows me a list of times I’ve linked to the page and the context.
I use this all the time with Logseq, but I find Logseq pretty unpolished, infrequently updated, etc., so I’m always on the lookout for something nicer.
I’m getting a Cloudflare error trying to access your demo site.
Also, do you support back linking? That’s a feature that’s very important to me.
I finally got around to setting up my internal services with TLS. It was surprisingly easy with a Caddy docker image supporting Cloudflare DNS challenge.
I did this because various services I use are starting to require https.
Now everything is on a custom domain, https, and I can access it through Tailscale as usual.
This is my favorite of the thread.
You can even call one Host, haha.
Lots of overcomplicated answers, imo.
Here’s what I did:
Now every device at home can hit all services by domain name over https. No need for any manual configuration on any client device (certs, hosts, etc.)
Bonus: Set up split DNS and subnet routing with Tailscale so that it uses the DNS server for that domain. Now any device connecting to the tailnet can connect to the services just like at home. No need to reconfigure apps, etc.
Simple and it works like magic.